Service Reference Variant

4.13 · Read Prepayment Configuration

Service details

Identifiers, rules, and applicability

Service reference
4.13
Service Reference Variant
4.13
DUIS section
3.8.37
Command variants
1, 2, 3
DUIS possible responses
AcknowledgementService Response from Device - GBCSPayloadResponse to a Command for Local Delivery Request - LocalCommand FormatCountersigned SMETS1 Response
Critical
No
Sensitive response
No
Protection against replay
No
On demand
Yes
Future dated
DSP
DSP scheduled
No
DCC only
No
SMETS1 applicability
Yes
SAPC requirement
Optional
DUIS applicability
3.0, 3.1, 4.0, 5.0, 5.1, 5.2, 5.3

Cross-specification evidence

SMETS/CHTS to GBCS Mapping

This section shows the SMETS and CHTS attributes that can be read or written by the identified GBCS Use Case. Command requirements are shown separately from the mapped attributes.

ECS26a13 attributes0x003BESME
SpecificationItemReferenceDescription
SMETSDebt Recovery per Payment [INFO]5.7.4.11The percentage of a payment to be recovered against debt when ESME is operating Payment-based Debt Recovery in Prepayment Mode.
SMETSDebt Recovery Rates [1 … 2] [INFO]5.7.4.12Two debt recovery rates in Currency Units per unit time for when ESME is using Time-based Debt Recovery in Prepayment Mode.
SMETSDebt Recovery Rate Cap [INFO]5.7.4.13The maximum amount in Currency Units per unit time that can be recovered through Payment-based Debt Recovery when ESME is operating in Prepayment Mode.
SMETSDisablement Threshold [INFO]5.7.4.15The threshold in Currency Units for controlling when to Disable the Supply.
SMETSEmergency Credit Limit [INFO]5.7.4.16The amount of Emergency Credit in Currency Units to be made available to a Consumer where Emergency Credit is activated.
SMETSEmergency Credit Threshold [INFO]5.7.4.17The threshold in Currency Units below which Emergency Credit Balance [INFO](5.7.5.15) may be activated if so configured when ESME is operating in Prepayment Mode.
SMETSLow Credit Threshold [INFO]5.7.4.23The threshold in Currency Units below which a low credit Alert is signalled.
SMETSMaximum Credit Threshold5.7.4.25The maximum credit which can be applied by any Add Credit Command.
SMETSMaximum Meter Balance Threshold5.7.4.27The Meter Balance [INFO](5.7.5.22) threshold in Currency Units above which an Add Credit Command is rejected.
SMETSNon-Disablement Calendar [INFO]5.7.4.30A Switching Table comprising a set of rules specifying periods during which the Supply will not be Disabled due to the Meter Balance [INFO](5.7.5.22) being below, or falling below, the Disablement Threshold [INFO](5.7.4.15) and, if Emergency Credit is activated, the Emergency Credit Balance [INFO](5.7.5.15) being, or falling to, zero, when ESME is operating in Prepayment Mode.
SMETSPayment Mode [INFO]5.7.4.31The current mode of operation, being Prepayment Mode or Credit Mode.
SMETSSuspend Debt Disabled5.7.4.45A setting controlling whether debt should be collected when ESME is operating in Prepayment Mode and Supply is Disabled.
SMETSSuspend Debt Emergency5.7.4.46A setting controlling whether standing charge and debt should be deducted from the Emergency Credit Balance [INFO](5.7.5.15) when ESME is operating in Prepayment Mode and Emergency Credit is in use.
GCS21b10 attributes0x00B5GSME
SpecificationItemReferenceDescription
SMETSDebt Recovery per Payment4.6.4.8The percentage of a payment to be recovered against debt when GSME is operating Payment-based Debt Recovery in Prepayment Mode.
SMETSDebt Recovery Rates [1 … 2]4.6.4.9Two debt recovery rates in Currency Units per unit time for when GSME is using Time-based Debt Recovery in Prepayment Mode.
SMETSDebt Recovery Rate Cap4.6.4.10The maximum amount in Currency Units per unit time that can be recovered through Payment-based Debt Recovery when GSME is operating in Prepayment Mode.
SMETSDisablement Threshold4.6.4.12The threshold in Currency Units for controlling when to Disable the Supply.
SMETSEmergency Credit Limit4.6.4.13The amount of Emergency Credit in Currency Units to be made available to a Consumer where Emergency Credit is activated.
SMETSEmergency Credit Threshold4.6.4.14The threshold in Currency Units below which Emergency Credit Balance(4.6.5.8) may be activated if so configured when GSME is operating in Prepayment Mode.
SMETSLow Credit Threshold4.6.4.16The threshold in Currency Units below which a low credit Alert is signalled.
SMETSMaximum Credit Threshold4.6.4.17The maximum credit which can be applied by any Add Credit Command.
SMETSMaximum Meter Balance Threshold4.6.4.18The Meter Balance(4.6.5.11) threshold in Currency Units above which an Add Credit Command is rejected.
SMETSNon-Disablement Calendar4.6.4.20A Switching Table comprising a set of rules specifying periods during which the Supply will not be Disabled due to the Meter Balance(4.6.5.11) being below, or falling below, the Disablement Threshold(4.6.4.12) and, if Emergency Credit is activated, the Emergency Credit Balance(4.6.5.8) being, or falling to, zero when GSME is operating in Prepayment Mode.

Specific Errors

Response codes and descriptions

No specific validation is defined for this SRV.

GBCS Use Case

Use cases, device coverage, and applicability

Use Case / Message Code
ECS26a0x003B
DUIS Applicability
v3.0 – v5.3
GBCS Applicability
v1.0 – v4.3
GBCS Criticality
Non-Critical
Sensitive Response
No
Future Dated
DSP
ResponseESMENot always GBT
SMETS1 Applicable
Yes
Eligible Roles
EISESME
Use Case / Message Code
GCS21b0x00B5
DUIS Applicability
v3.0 – v5.3
GBCS Applicability
v1.0 – v4.3
GBCS Criticality
Non-Critical
Sensitive Response
No
Future Dated
DSP
GBT
No
SMETS1 Applicable
Yes
Eligible Roles
GISGSMEGPF

DUIS Service Definition

Data items and DCC processing

Request data items

Table 150: ReadPrepaymentConfiguration (sr:ReadDataOnDemandOrFutureDated) data items
Data ItemDescription / Allowable valuesTypeMandatoryDefaultUnits
ExecutionDateTimeA User shall only add this Data Item to the Service Request where they require the Service Request to be executed at a future date and time. The UTC date and time the User requires the command to be executed on the Device Date-time in the future that is either <= current date + 30 days or the date = ‘3000-12-31T00:00:00Z’xs:dateTimeNoNoneUTC Date-Time

Message Patterns & Examples

Pattern explorer

Open Message Patterns →

SMETS1 Supporting Requirements

Device-model variations and equivalent steps

Review the Section 18 requirements and their applicability across the documented manufacturer, Device Type, model, and firmware profiles.

Open S1SR Requirements →