| LowerBandSubGHzChannels0To26 | Sets the configuration of the Sub GHz Channel Masks for the data item “Page 28 Mask” as defined by GBCS (each page equates to a set of channels that could be used in a specific frequency range)
Sets list of channels 0 to 26 in the Lower Band Sub GHz (863 to 876 MHz) frequency range. See Response Code E062801
By including a Channel number within the SR this shall mean ‘channel can be used by the Communications Hub’
By NOT including a Channel number within the SR this shall mean ‘channel cannot be used by the CH’
. Please see Annex to SEC Section F4 – where Pages are used, at least two channels must be configured per Page. See Response Code E062802 | sr:Channels0To26
(Sequence of Channel0 sr:NoType to Channel26 sr:NoType, all optional, but a minimum of 2 Channels must be set) | LowerBandSubGHzChannels0To26 | None | N/A |
| LowerBandSubGHzChannels27To34 | Sets the configuration of the Sub GHz Channel Masks for the data item “Page 29 Mask” as defined by GBCS (each page equates to a set of channels that could be used in a specific frequency range)
Sets list of channels 27 to 34 in the Lower Band Sub GHz (863 to 876 MHz) frequency range. See Response Code E062801
By including a Channel number within the SR this shall mean ‘channel can be used by the Communications Hub’
By NOT including a Channel number within the SR this shall mean ‘channel cannot be used by the CH’
Please see Annex to SEC Section F4 - where Pages are used, at least two channels must be configured per Page. See Response Code E062802 | sr:Channels27To34
(Sequence of Channel27 sr:NoType to Channel34 sr:NoType, all optional, but a minimum of 2 Channels must be set) | Yes | None | N/A |
| LowerBandSubGHzChannels35To61 | Sets the configuration of the Sub GHz Channel Masks for the data item “Page 30 Mask” as defined by GBCS (each page equates to a set of channels that could be used in a specific frequency range)
Sets list of channels 35 to 61 in the Lower Band Sub GHz (863 to 876 MHz) frequency range. See Response Code E062801
By including a Channel number within the SR this shall mean ‘channel can be used by the Communications Hub’
By NOT including a Channel number within the SR this shall mean ‘channel cannot be used by the CH’.
Please see Annex to SEC Section F4 - where Pages are used, at least two channels must be configured per Page. See Response Code E062802 | sr:Channels35To61
(Sequence of Channel35 sr:NoType to Channel61 sr:NoType, all optional, but a minimum of 2 Channels must be set) | Yes | None | N/A |
| UpperBandSubGHzChannels0To26 | Sets the configuration of the Sub GHz Channel Masks for the data item “Page 31 Mask” as defined by GBCS (each page equates to a set of channels that could be used in a specific frequency range)
List of channels 0 to 26 in the Upper Band Sub GHz (915 to 921 MHz) frequency range. See Response Code E062801
By including a Channel number within the SR this shall mean ‘channel can be used by the Communications Hub’
By NOT including a Channel number within the SR this shall mean ‘channel cannot be used by the CH’.
This data item should be empty, but this is not validated by the DCC. | sr:Channels0To26
(Sequence of Channel0 sr:NoType to Channel26 sr:NoType, all optional) | Yes | None | N/A |
| NormalLimitedDutyCycleThreshold | As defined in GBCS section 10.6.2.3.
Valid Set:
Percentage value between 0.5 and 2.0 % | Restriction of
xs:decimal
(fractionDigits = 1, minInclusive = 0.5, maxInclusive = 2.0) | Yes | None | % |
| LimitedCriticalDutyCycleThreshold | As defined in GBCS section 10.6.2.3.
Valid Set:
Percentage value between 1.5 and 2.5 % and greater than NormalLimitedDutyCycleThreshold | Restriction of
xs:decimal
(fractionDigits = 1, minExclusive = 1.5, maxExclusive = 2.5) | Yes | None | % |
| MaximumSubGHzChannelChangesPerWeek | The CHF shall not undertake more than this number of Channel Changes per week except where the one or more additional channel changes results from ‘DBCH05 Request CHF Sub GHz Channel Scan’ Command(s). See clause 3.8.82
Valid Set:
Value between 1 and 7 | Restriction of
xs:unsignedShort
(minInclusive = 1, maxInclusive = 7) | Yes | None | N/A |
| GSMECurfew | The numbers of hours without GSME communications before the CHF determines the GSME to be a ‘Lost GSME’
When the CHF identifies that there is a ‘Lost GSME’, it shall take actions as defined in GBCS section 10.6.2.6.
Valid Set:
Value > 1 | Restriction of
xs:unsignedShort
(minExclusive = 1) | Yes | None | Hours |
| ChannelQuieterThreshold | Shall be the minimum number of decibels by which an alternative channel needs to be quieter, in the conditions defined in GBCS section 10.6.2.8.
Valid Set:
Value between 1 and 255 | Restriction of
xs:unsignedShort
(minInclusive = 1, maxInclusive = 255) | Yes | None | dB |
| ChannelNoisierThreshold | Shall be the maximum number of decibels by which an alternative channel may be noisier, in the conditions defined in GBCS section 10.6.2.8.
Valid Set:
Value between 0 and 20 | Restriction of
xs:unsignedShort
(minInclusive = 0, maxInclusive = 20) | Yes | None | dB |
| NonGSMEPoorCommsPercentageThreshold | The number of 30 minute periods over which assessment of non GSME Device poor communications reports is made by the CH. See GBCS section 10.6.2.6 for details.
Valid Set:
Value between 1.00 and 100.00% | Restriction of
xs:decimal
(fractionDigits = 2, minInclusive = 1.00, maxInclusive = 100.00) | Yes | None | % |
| NonGSMEPoorCommsMeasurementPeriods | The number of 30 minute periods over which assessment of non GSME Device poor communications reports is made by the CH
Valid Set:
Value between 50 and 150 | Restriction of
xs:unsignedShort
(minInclusive = 50, maxInclusive = 150) | Yes | None | N/A |
| LocalCHNoiseMeasurementPeriod | The number of trailing minutes over which the CHF shall assess its own percentage of retried messages.
Valid Set:
Value > 60 | Restriction of
xs:unsignedShort
(minExclusive = 60) | Yes | None | Minutes |
| LocalCHFailurePercentage | As defined in GBCS section 10.6.2.6.
Valid Set:
Value between 1.00 and 100.00% | Restriction of
xs:decimal
(fractionDigits = 2, minInclusive = 1.00, maxInclusive = 100.00) | Yes | None | % |
| LocalCHRetryPercentage | As defined in GBCS section 10.6.2.6.
Valid Set:
Value between 1.00 and 100.00% | Restriction of
xs:decimal
(fractionDigits = 2, minInclusive = 1.00, maxInclusive = 100.00) | Yes | None | % |